BOILER ACCESSORIES



SWEETCORN TECH




LAYANAN :

    Pemasangan baru
    Konsultasi sistem
    Pemeliharaan besar dan Cleaning
    Sistem mekanik

Perusahaan terbaik dan terpercaya dalam pengerjaan dan perawatan besar Boiler di perusahaan anda



Boiler fittings and accessories


    Pressuretrols to control the steam pressure in the boiler. Boilers generally have 2 or 3 pressuretrols: An manual-reset pressuretrol, which functions as a safety by setting the upper limit of steam pressure, the Operating pressuretrol, which controls when the boiler fires to maintain pressure, and for boilers equipped with a modulating burner, a modulating pressuretrol which controls the amount of fire.
    Safety valve: It is used to relieve pressure and prevent possible explosion of a boiler.
    Water level indicators: They show the operator the level of fluid in the boiler, also known as a sight glass, water gauge or water column is provided.
    Bottom blowdown valves: They provide a means for removing solid particulates that condense and lie on the bottom of a boiler. As the name implies, this valve is usually located directly on the bottom of the boiler, and is occasionally opened to use the pressure in the boiler to push these particulates out.
    Continuous blowdown valve: This allows a small quantity of water to escape continuously. Its purpose is to prevent the water in the boiler becoming saturated with dissolved salts. Saturation would lead to foaming and cause water droplets to be carried over with the steam - a condition known as priming. Blowdown is also often used to monitor the chemistry of the boiler water.
    Flash Tank: High-pressure blowdown enters this vessel where the steam can 'flash' safely and be used in a low-pressure system or be vented to atmosphere while the ambient pressure blowdown flows to drain.
    Automatic Blowdown/Continuous Heat Recovery System: This system allows the boiler to blowdown only when makeup water is flowing to the boiler, thereby transferring the maximum amount of heat possible from the blowdown to the makeup water. No flash tank is generally needed as the blowdown discharged is close to the temperature of the makeup water.
    Hand holes: They are steel plates installed in openings in "header" to allow for inspections & installation of tubes and inspection of internal surfaces.
    Steam drum internals, A series of screen, scrubber & cans (cyclone separators).
    Low- water cutoff: It is a mechanical means (usually a float switch) that is used to turn off the burner or shut off fuel to the boiler to prevent it from running once the water goes below a certain point. If a boiler is "dry-fired" (burned without water in it) it can cause rupture or catastrophic failure.
    Surface blowdown line: It provides a means for removing foam or other lightweight non-condensible substances that tend to float on top of the water inside the boiler.
    Circulating pump: It is designed to circulate water back to the boiler after it has expelled some of its heat.
    Feedwater check valve or clack valve: A non-return stop valve in the feedwater line. This may be fitted to the side of the boiler, just below the water level, or to the top of the boiler.[7]
    Top feed: In this design for feedwater injection, the water is fed to the top of the boiler. This can reduce boiler fatigue caused by thermal stress. By spraying the feedwater over a series of trays the water is quickly heated and this can reduce limescale.
    Desuperheater tubes or bundles: A series of tubes or bundles of tubes in the water drum or the steam drum designed to cool superheated steam, in order to supply auxiliary equipment that does not need, or may be damaged by, dry steam.
    Chemical injection line: A connection to add chemicals for controlling feedwater pH.



Steam accessories


    Main steam stop valve:
    Steam traps:
    Main steam stop/Check valve: It is used on multiple boiler installations.

Combustion accessories


    Fuel oil system:fuel oil heaters
    Gas system:
    Coal system:
    Soot blower

Other essential items


    Pressure gauges:
    Feed pumps:
    Fusible plug:
    Inspectors test pressure gauge attachment:
    Name plate:
    Registration plate:

Gas safe check


    It is essential to carry out gas safe check each year:


CLICK TO CONTACT US 

Tidak ada komentar:

Posting Komentar

PT BYWOS MULTI SOLUTION didukung oleh tenaga kerja terampil, penuh insinyur pengalaman dan dukungan finansial yang kuat untuk melaksanakan pasokan peralatan, Konstruksi, Fabrikasi, merancang proyek dari konsep awal sampai commissioning stage perusahaan Anda.